Seat Alhambra Key Problems
Seat's family MPV jumbo is among the best in the market when it comes to keeping resales value. And with a brand new model on sale, it's better than ever.
There are a variety of reasons why your key fob could not function properly, including a dead battery water damage, receiver module issues or signal interference. This article will walk you through the steps to get it working.
Water Damage
If your seat alhambra keyfob is able to survive a wash cycle or a bath in the pool or ocean then it's probably equipped with an incredible waterproof chip, but do not make it a habit because exposure to water in excess increases the risk of the key fob being damaged. If your key fob ceases to functioning after exposure to rain or clean tap water, you should remove the battery and wipe the electronic component using a towel. Dry it completely before replacing the battery. In the event of exposure to soapy or salty water, it is recommended to clean the chip with alcohol, isopropyl or electronic cleaner prior to trying to put the battery back in.
Faulty Receiver Module
If you've tried a new battery for a button and the key fob does not lock or unlock, it's likely the receiver module has found a fault. It's a fairly simple and affordable fix. You can unplug the 12 volt battery for a couple of minutes (first take off the negative cable, then press the horn numerous times) to drain any remaining power. Then connect it in reverse. positive cable first then negative cable later.
ESP Warning Light – If the ESP symbol is illuminated, this is normal. It is a sign that you are driving on terrain that has poor traction. This could be due to snow, gravel or surface water. If the ESP warning light is constantly illuminated it indicates that there is a problem within the system. It should be detected with a iCarsoft i908 Seat OBD Code Reader, which will provide a precise fault description.
Dead Coin Battery
One of the most frequent reasons for the seat alhambra keys to stop working is a dead battery. The key fob has an insignificant button cell battery which keeps it powered. Replace it with a brand new battery that has the exact dimensions, voltage and specs as the original. If you're replacing the battery, be sure to remove all metal retaining clips from the back of the key fob. You should also make sure that the contact points are free of corrosion.
If the key fob was exposed to water (such as rain or soapy tap water), it is recommended to remove and clean the chip with an electronic cleaner or isopropyl ethanol before installing a new battery. The chip is susceptible to moisture and could be permanently damaged. If the key fob still isn't working after replacing the battery it may be necessary for you to replace the key fob.
Faulty Receiver Module
If your key fob stopped working after replacing the battery, but it did not function, or stopped working suddenly your receiver module might have experienced a malfunction. The receiver module is responsible for absorbing the radio frequency signals sent by your remote key fob and converting them into electrical commands that are then utilized by other modules in your car.
If the receiver module has suffered a malfunction it will not respond to any of the commands issued by your remote key fob. In this case you'll need to visit a dealer to reprogramme your key fob and a new receiver module.
The key fob features rubber seals that block water from entering the electronic chip inside. If you immerse the key fob into soapy or salty water, it may damage the chips. If your key fob isn't able to work, you could try cleaning the chip using isopropyl or electronic cleaner.
If the keys are connected but the receiver module has developed a fault, you may try to restart all electronics on board by disconnecting the battery at 12 volts for a few minutes. Then reconnect the battery in reverse order (negative cable first and then positive). This resets all the electronic components on board and restore their functionality.
A malfunctioning electronic chip
The key fob houses a small electronic chip that transmits a signal to the receiver module whenever the key is used. If the signal received does not match the one recorded by the car the immobilizer will shut down the engine and stop the vehicle from starting. If the key fob does not work and you aren't able to reprogram it, it could be due to a faulty microchip.
seat keys inside the key fob isn't permanent to the device and might have to be replaced to get it working again. This can be accomplished by getting the key fob removed from its housing and using a needle or pin to make contact with each metal retaining clip. If the clips are corroded, or broken, you will require replacement in order for the remote control to work. Make sure that any replacement batteries are the same size, voltage, and specifications as the original one.
Seat Alhambra is a well-known and well-designed model, may have problems with certain components or equipment. For instance there are owners who have had issues with the auto climate control system, which may be faulty and get stuck in one specific setting. Similarly, the infotainment system has also been reported to malfunction and freeze screens.